Nd YVO4 Crystal-manufacture,factory,supplier from China

Research BackgroundLithium Yttrium Fluoride (LiYF4, YLF) crystal has many excellent properties such as low melting point, low phonon energy, small thermal lens effect, natural polarization, etc. It is a laser matrix material with excellent performance. YLF belongs to the tetragonal structure of scheelite, and the space group is I41/a.

03 Experimental results and analysisWhen the green light input power is lower than 4 W, the matching temperature of the BBO crystal has little effect on the output power of the quadrupled 266 nm laser, and when the optimal power of ultraviolet light output is achieved, the temperature offset ΔT of the heating device also tends to be consistent; when the green light input power is greater than 8 W, the higher the matching temperature of the BBO crystal (www.wisoptic.com), the smaller the temperature offset ΔT of the heating device, and the higher the output power of the 266 nm la

3 The main application of lithium tantalate crystal3.2 OscillatorAn oscillator is an energy conversion device that converts DC power into AC power with a certain frequency. This circuit is called an oscillation circuit. The oscillator achieves free oscillation through the mutual conversion between magnetic field energy and electric field energy.Oscillators are divided into RC oscillators, LC oscillators and crystal oscillators. The crystal oscillator has a piezoelectric effect, and the crystal will deform when a voltage is applied to the two poles of the wafer.

04 Theoretical study of thermal properties The above experiment shows that the BBO crystal (www.wisoptic.com) generates serious heat in the process of frequency quadrupling. It is known that the energy band gap of the BBO crystal is 6.56 eV, while the single photon energy of 266 nm and 532 nm lasers is 4.66 eV and 2.33 eV respectively. Theoretically, the crystal does not have single photon absorption of 266 nm and 532 nm lasers.

2.3 Lithium tantalate single crystal filmAfter the 1980s, thin film preparation technology has developed rapidly. Currently, the commonly used preparation technologies of lithium tantalate single crystal (www.wisoptic.com) thin film mainly include chemical vapor deposition, physical vapor deposition, magnetron sputtering and sol-gel method.The chemical vapor deposition method synthesizes a thin film on a substrate through a chemical reaction and accurately controls the chemical composition of the product. It has the characteristics of low stress and good quality.

1.3 Doping of Lithium Tantalate CrystalDifferent fields have different requirements for the properties of lithium tantalate crystals. When being used to prepare high-density and large-capacity holographic information storage devices, LiTaO3 crystals need to have excellent photorefractive properties. Due to the particularity of the crystal structure of LiTaO3, its physical properties can be adjusted through doping, for example, the widely used photorefractive doping.

2. Theoretical analysis2.1 Temperature robustnessTemperature robustness refers to the stability of the frequency-doubled crystal with respect to temperature. Specifically, when the temperature fluctuates, the power of the frequency-doubled light will not be greatly affected. The influence of temperature on the frequency doubling process mainly comes from the influence on the phase mismatch.

2. Theoretical analysis2.2 Design of CPPLN crystal structureIn order to achieve better temperature robustness and higher frequency doubling efficiency on the same CPPLN crystal, we designed the crystal structure of CPPLN. The schematic diagram of CPPLN for frequency doubling from 1064nm to 532nm is shown in Figure 1. The incident beam with fundamental frequency is set to be e-light, that is, its polarization direction is horizontal. At the same time, the output beam is also set to be e-light.

IntroductionLithium tantalate (LiTaO3, referred to as LT), as an excellent multifunctional crystal material, has good piezoelectric, electro-optical and pyroelectric properties, and is ideal for making surface acoustic wave (SAW) filters, resonators, tuners, Q switches and pyroelectric detectors. Devices made from LT crystal (www.wisoptic.com) are widely used in the automotive electronics, 5G communications and infrared detectors, and have broad market prospects.In 1965, Ballman used the pulling method to grow LT single crystal for the first time.

4. Experimental Result and Analysis4.1 Comparison of frequency doubling efficiency of CPPLN and LBOThe CPPLN crystal (www.wisoptic.com) we designed has the maximum frequency doubling efficiency in the working range between 15-40℃, so the subsequent analysis will be carried out around this range. In the same fundamental frequency light power gradient, the effect of temperature change on the frequency doubling efficiency of CPPLN is shown in Figure 4(a).